Have you ever wondered that from where the fluid comes out that cleans your windshield? Well, the wipers clean the windshield through the fluid that is stored in the windshield washer reservoir. It is a simple container that is made from rugged polyethylene plastic, and therefore it eventually develops cracks and starts leaking that demands immediate replacements.
While repairing most of the automotive parts requires expertise and experience; however, the process of changing the windshield washer reservoir can be done quickly. So let’s just read on and find out how to replace it.
Replacing A Windshield Washer Reservoir
The process breaks down into simple, generic steps. Remember that before you get your hands directly on your car, you must go for a manual for replacement instructions as it may differ in every vehicle.
So before you start with the repair job, you need to take all the. Park your car in the ventilated area with an entirely flat surface. Switch off the ignition and apply the emergency brake. Also, it is very crucial to protect your eyes, so don’t forget to put on safety goggles.
A guide to removing the Old Windshield Washer Fluid Reservoir
- Disconnect the negative cable from the battery and isolate it
- Lift the vehicle on jack stands
- Remove obstructing parts on the way
- Detach the wires from the reservoir
- Separate the washer hose and clear out the contents from the reservoir.
- Take off the fasteners
- Now remove the reservoir and take out the windshield washer pump
- Install the new reservoir
- Finally, reinstall the components
Installing The New Windshield Washer Reservoir
So now that once you have taken out the old reservoir, let’s check out the guide on installing the new reservoir.
- Put the windshield washer pump into the reservoir.
- Install the windshield washer reservoir
- Introduce the fasteners to the reservoir. Using a wrench or ratchet, tighten the bolts.
- Fix the washer hose to the pump and fill up the reservoir with washer fluid
- You can now bring down the vehicle from jack stands.
- Attach the negative cable to the battery.
The Right Time To Replace The Windshield Washer Reservoir
Just like other car parts, the windshield washer reservoir can fail to work before its designated life. And in such a case, it becomes mandatory to replace it to ensure its proper functionality. You can buy it online at The Auto Parts Shop.
Reasons that might interrupt the functionality of the reservoir and demands for the replacement:
Cracks – Usually, frozen washer fluid causes cracks in the reservoir. Also, the engine vibrations or the shocks while driving over rough surfaces damage the reservoir. Seals – Sometimes, the seals around the connection point between the hoses and the reservoir fail to work.
Some various signs and symptoms show up when the condition of the reservoir worsens.
Some of the easily noticeable warning signs include:
- Uneven sprays over the windshield
- Washer fluid stops coming out.
- There is leakage in the area of the reservoir.
Melting Ice in Reservoir
Now, as you know that the freezing fluids might cause cracks in the reservoir. Here are some of the simple maintenance processes to melt and dry the reservoir.
Defrosting a frozen reservoir:
There are washer fluids available in the market that contain a cleaning agent within themselves. Check out for the freeze-resistant liquids that won’t freeze in low temperatures.
There are specific ways to warm up the frozen windshield washer reservoir. If you have enough time and a heated garage, you can park your vehicle there so that it gets warm. In case you want immediate ice melting, direct a hairdryer at the hoses and the reservoir. Heating pads can also be used in the lower half of the reservoir.
Lastly, the reservoir can be removed following the steps mentioned above. The container should be placed inside a bucket to prevent spills and then finally placed near the warm space or heater vent.
Once the fluid that is frozen melts, it has to be drained from the system. Also, before refilling the freeze-resistant washer fluid in the reservoir, you must check for cracks or leaks.
Draining The Washer Fluid Reservoir
The reservoir requires draining to get rid of old washer fluid that becomes dirty. Also, removing it is necessary to replace the old fluid with freeze-resistant fluid before winters.
Triggering the windshield washers is an effortless way to drain the reservoir. Also, you can disconnect the hoses from appliances if you want to conserve washer fluid. And if you are unable to separate the hoses from washers, make use of handpumps or turkey baster that In case you cannot separate the hoses from the washers, use a hand pump or turkey baster can help you to siphon the contents into a separate container.